Revision history [back]

I have two separate access points in my home, one for bedroom and one for living room, since this works the best in my home. With 1.0.7.16 my Jolla used to switch between them quite well but now with 1.0.8.19 the switching happens rarely if at all.

On Tuesday morning (15/07/2014) I did get my Jolla to switch to the living rooms access point but it took it ~20-40 minutes to do so. Now with Wednesday (16th) it hasn't done it and it's been over an hour by now. I've observed the Wifi-signal icon and it does seem to get weaker every now and then, even down to one bar, but it still won't switch to my living rooms access point, even though it's quite close to the phone (~1 meter).

Only change that I can think of is that on Tuesday morning I had 1.0.8.19 installed as over-the-air update. During Tuesday I had my phone restored directly to 1.0.8.19 by service.

I have two separate access points in my home, one for bedroom and one for living room, since this works the best in my home. With 1.0.7.16 my Jolla used to switch between them quite well but now with 1.0.8.19 the switching happens rarely if at all.

On Tuesday morning (15/07/2014) I did get my Jolla to switch to the living rooms access point but it took it ~20-40 minutes to do so. Now with Wednesday (16th) it hasn't done it and it's been over an hour by now. I've observed the Wifi-signal icon and it does seem to get weaker every now and then, even down to one bar, but it still won't switch to my living rooms access point, even though it's quite close to the phone (~1 meter).

Only change that I can think of is that on Tuesday morning I had 1.0.8.19 installed as over-the-air update. During Tuesday I had my phone restored directly to 1.0.8.19 by service.

I have two separate access points in my home, one for bedroom and one for living room, since this works the best in my home. With 1.0.7.16 my Jolla used to switch between them quite well but now with 1.0.8.19 the switching happens rarely if at all.

On Tuesday morning (15/07/2014) I did get my Jolla to switch to the living rooms access point but it took it ~20-40 minutes to do so. Now with Wednesday (16th) it hasn't done it and it's been over an hour by now. I've observed the Wifi-signal icon and it does seem to get weaker every now and then, even down to one bar, but it still won't switch to my living rooms access point, even though it's quite close to the phone (~1 meter).

Only change that I can think of is that on Tuesday morning I had 1.0.8.19 installed as over-the-air update. During Tuesday I had my phone restored directly to 1.0.8.19 by service.

UPDATE: Automatic switching didn't happen to living room unless I manually triggered it with Wifi off/on, Airplane mode visiting of or just turning off the access point from Settings. Below is also my network setup.

Living room: Apple Time Capsule (3rd gen) Limited to 802.11b/g/n on 2.4 GHz, WPA2 Personal (AES), channel 4. Also broadcasts my 5 GHz network which is limited to 802.11n and has automatic channel (100).

Bedroom: Apple AirPort Express (1st gen) Limited to 802.11n (2.4 GHz broadcast only), WPA2 Personal (AES), channel 3.

I changed the channel on bedroom from 3 to 9 and that didn't seem to have any effect on the automatic switching. I changed it back to 3 since that used to work with 1.0.7.16. Might change these again later.

I have two separate access points Wifi networks in my home, one for bedroom and one for living room, since this works the best in my home. With 1.0.7.16 my Jolla used to switch between them quite well but now with 1.0.8.19 the switching happens rarely if at all.

On Tuesday morning (15/07/2014) I did get my Jolla to switch to the living rooms access point network but it took it ~20-40 minutes to do so. Now with Wednesday (16th) it hasn't done it and it's been over an hour by now. I've observed the Wifi-signal icon and it does seem to get weaker every now and then, even down to one bar, but it still won't switch to my living rooms access point, network, even though it's quite close to the phone (~1 meter).

Only change that I can think of is that on Tuesday morning I had 1.0.8.19 installed as over-the-air update. During Tuesday I had my phone restored directly to 1.0.8.19 by service.

UPDATE: Automatic switching didn't happen to living room unless I manually triggered it with Wifi off/on, Airplane mode visiting or just turning off the access point network from Settings. Below is also my network setup.

Living room: Apple Time Capsule (3rd gen) Limited to 802.11b/g/n on 2.4 GHz, WPA2 Personal (AES), channel 4. Also broadcasts my 5 GHz network which is limited to 802.11n and has automatic channel (100).

Bedroom: Apple AirPort Express (1st gen) Limited to 802.11n (2.4 GHz broadcast only), WPA2 Personal (AES), channel 3.

I changed the channel on bedroom from 3 to 9 and that didn't seem to have any effect on the automatic switching. I changed it back to 3 since that used to work with 1.0.7.16. Might change these again later.

I have two separate Wifi networks in my home, one for bedroom and one for living room, since this works the best in my home. With 1.0.7.16 my Jolla used to switch between them quite well but now with 1.0.8.19 the switching happens rarely if at all.

On Tuesday morning (15/07/2014) I did get my Jolla to switch to the living rooms network but it took it ~20-40 minutes to do so. Now with Wednesday (16th) it hasn't done it and it's been over an hour by now. I've observed the Wifi-signal icon and it does seem to get weaker every now and then, even down to one bar, but it still won't switch to my living rooms network, even though it's quite close to the phone (~1 meter).

Only change that I can think of is that on Tuesday morning I had 1.0.8.19 installed as over-the-air update. During Tuesday I had my phone restored directly to 1.0.8.19 by service.

UPDATE: Automatic switching didn't happen to living room unless I manually triggered it with Wifi off/on, Airplane mode visiting or just turning off the network from Settings. Below is also my network setup.

Living room: Apple Time Capsule (3rd gen) Limited to 802.11b/g/n on 2.4 GHz, WPA2 Personal (AES), channel 4. Also broadcasts my 5 GHz network which is limited to 802.11n and has automatic channel (100).

Bedroom: Apple AirPort Express (1st gen) Limited to 802.11n (2.4 GHz broadcast only), WPA2 Personal (AES), channel 3.

I changed the channel on bedroom from 3 to 9 and that didn't seem to have any effect on the automatic switching. I changed it back to 3 since that used to work with 1.0.7.16. Might change these again later.

Minor update: I changed "access point" to "network" since this can be misunderstood. Feel free to revert this.

I have two separate Wifi networks in my home, one for bedroom and one for living room, since this works the best in my home. With 1.0.7.16 my Jolla used to switch between them quite well but now with 1.0.8.19 the switching happens rarely if at all.

On Tuesday morning (15/07/2014) I did get my Jolla to switch to the living rooms network but it took it ~20-40 minutes to do so. Now with Wednesday (16th) it hasn't done it and it's been over an hour by now. I've observed the Wifi-signal icon and it does seem to get weaker every now and then, even down to one bar, but it still won't switch to my living rooms network, even though it's quite close to the phone (~1 meter).

Only change that I can think of is that on Tuesday morning I had 1.0.8.19 installed as over-the-air update. During Tuesday I had my phone restored directly to 1.0.8.19 by service.

UPDATE: Automatic switching didn't happen to living room unless I manually triggered it with Wifi off/on, Airplane mode visiting or just turning off the network from Settings. Below is also my network setup.

Living room: Apple Time Capsule (3rd gen) Limited to 802.11b/g/n on 2.4 GHz, WPA2 Personal (AES), channel 4. Also broadcasts my 5 GHz network which is limited to 802.11n and has automatic channel (100).

Bedroom: Apple AirPort Express (1st gen) Limited to 802.11n (2.4 GHz broadcast only), WPA2 Personal (AES), channel 3.

I changed the channel on bedroom from 3 to 9 and that didn't seem to have any effect on the automatic switching. I changed it back to 3 since that used to work with 1.0.7.16. Might change these again later.

Minor update: I changed "access point" to "network" since this can be misunderstood. Feel free to revert this.If there's still an issue with this please point it out in the comments or if you can (this is not Wiki-post yet so not everyone can) edit the message directly.

I have two separate Wifi networks in my home, one for bedroom and one for living room, since this works the best in my home. With 1.0.7.16 my Jolla used to switch between them quite well but now with 1.0.8.19 the switching happens rarely if at all.

On Tuesday morning (15/07/2014) I did get my Jolla to switch to the living rooms network but it took it ~20-40 minutes to do so. Now with Wednesday (16th) it hasn't done it and it's been over an hour by now. I've observed the Wifi-signal icon and it does seem to get weaker every now and then, even down to one bar, but it still won't switch to my living rooms network, even though it's quite close to the phone (~1 meter).

Only change that I can think of is that on Tuesday morning I had 1.0.8.19 installed as over-the-air update. During Tuesday I had my phone restored directly to 1.0.8.19 by service.

UPDATE: Automatic switching didn't happen to living room unless I manually triggered it with Wifi off/on, Airplane mode visiting or just turning off the network from Settings. Below is also my network setup.

Living room: Apple Time Capsule (3rd gen) Limited to 802.11b/g/n on 2.4 GHz, WPA2 Personal (AES), channel 4. Also broadcasts my 5 GHz network which is limited to 802.11n and has automatic channel (100).

Bedroom: Apple AirPort Express (1st gen) Limited to 802.11n (2.4 GHz broadcast only), WPA2 Personal (AES), channel 3.

I changed the channel on bedroom from 3 to 9 and that didn't seem to have any effect on the automatic switching. I changed it back to 3 since that used to work with 1.0.7.16. Might change these again later.

Minor update: I changed "access point" to "network" since this can be misunderstood. If there's still an issue with this please point it out in the comments or if you can (this is not Wiki-post yet so not everyone can) edit the message directly.

I have two separate Wifi networks in my home, one for bedroom and one for living room, since this works the best in my home. With 1.0.7.16 my Jolla used to switch between them quite well but now with 1.0.8.19 the switching happens rarely if at all.

On Tuesday morning (15/07/2014) I did get my Jolla to switch to the living rooms network but it took it ~20-40 minutes to do so. Now with Wednesday (16th) it hasn't done it and it's been over an hour by now. I've observed the Wifi-signal icon and it does seem to get weaker every now and then, even down to one bar, but it still won't switch to my living rooms network, even though it's quite close to the phone (~1 meter).

Only change that I can think of is that on Tuesday morning I had 1.0.8.19 installed as over-the-air update. During Tuesday I had my phone restored directly to 1.0.8.19 by service.

UPDATE: Automatic switching didn't happen to living room unless I manually triggered it with Wifi off/on, Airplane mode visiting or just turning off the network from Settings. Below is also my network setup.

Living room: Apple Time Capsule (3rd gen) Limited to 802.11b/g/n on 2.4 GHz, WPA2 Personal (AES), channel 4. Also broadcasts my 5 GHz network which is limited to 802.11n and has automatic channel (100).

Bedroom: Apple AirPort Express (1st gen) Limited to 802.11n (2.4 GHz broadcast only), WPA2 Personal (AES), channel 3.

I changed the channel on bedroom from 3 to 9 and that didn't seem to have any effect on the automatic switching. I changed it back to 3 since that used to work with 1.0.7.16. Might change these again later.

Minor update:update 1: I changed "access point" to "network" since this can be misunderstood. If there's still an issue with misunderstood. Minor update 2: I don't have this please point it out setup anymore in the comments or if you can (this use so this is not Wiki-post yet so not everyone can) edit the message directly.now a wiki post.

I have two separate Wifi networks in my home, one for bedroom and one for living room, since this works the best in my home. With 1.0.7.16 my Jolla used to switch between them quite well but now with 1.0.8.19 the switching happens rarely if at all.

On Tuesday morning (15/07/2014) I did get my Jolla to switch to the living rooms network but it took it ~20-40 minutes to do so. Now with Wednesday (16th) it hasn't done it and it's been over an hour by now. I've observed the Wifi-signal icon and it does seem to get weaker every now and then, even down to one bar, but it still won't switch to my living rooms network, even though it's quite close to the phone (~1 meter).

Only change that I can think of is that on Tuesday morning I had 1.0.8.19 installed as over-the-air update. During Tuesday I had my phone restored directly to 1.0.8.19 by service.

UPDATE: Automatic switching didn't happen to living room unless I manually triggered it with Wifi off/on, Airplane mode visiting or just turning off the network from Settings. Below is also my network setup.

Living room: Apple Time Capsule (3rd gen) Limited to 802.11b/g/n on 2.4 GHz, WPA2 Personal (AES), channel 4. Also broadcasts my 5 GHz network which is limited to 802.11n and has automatic channel (100).

Bedroom: Apple AirPort Express (1st gen) Limited to 802.11n (2.4 GHz broadcast only), WPA2 Personal (AES), channel 3.

I changed the channel on bedroom from 3 to 9 and that didn't seem to have any effect on the automatic switching. I changed it back to 3 since that used to work with 1.0.7.16. Might change these again later.

Minor update 1: I changed "access point" to "network" since this can be misunderstood. misunderstood.

Minor update 2: I don't have this setup anymore in use so this is now a wiki post.

I have two separate Wifi networks in my home, one for bedroom and one for living room, since this works the best in my home. With 1.0.7.16 my Jolla used to switch between them quite well but now with 1.0.8.19 the switching happens rarely if at all.

On Tuesday morning (15/07/2014) I did get my Jolla to switch to the living rooms network but it took it ~20-40 minutes to do so. Now with Wednesday (16th) it hasn't done it and it's been over an hour by now. I've observed the Wifi-signal icon and it does seem to get weaker every now and then, even down to one bar, but it still won't switch to my living rooms network, even though it's quite close to the phone (~1 meter).

Only change that I can think of is that on Tuesday morning I had 1.0.8.19 installed as over-the-air update. During Tuesday I had my phone restored directly to 1.0.8.19 by service.

UPDATE: Automatic switching didn't happen to living room unless I manually triggered it with Wifi off/on, Airplane mode visiting or just turning off the network from Settings. Below is also my network setup.

Living room: Apple Time Capsule (3rd gen) Limited to 802.11b/g/n on 2.4 GHz, WPA2 Personal (AES), channel 4. Also broadcasts my 5 GHz network which is limited to 802.11n and has automatic channel (100).

Bedroom: Apple AirPort Express (1st gen) Limited to 802.11n (2.4 GHz broadcast only), WPA2 Personal (AES), channel 3.

I changed the channel on bedroom from 3 to 9 and that didn't seem to have any effect on the automatic switching. I changed it back to 3 since that used to work with 1.0.7.16. Might change these again later.

Minor update 1: Jul 18 '14: I changed "access point" to "network" since this can be misunderstood.

Minor update 2: Aug 12 '14: I don't have this setup anymore in use so this is now a wiki post.