micro SD not recognized anymore [not relevant]
asked 2015-11-03 00:20:37 +0200
My jolla doesn't recognize my microSD card anymore. Neither does /dev/mmcblk1 appear nor does the CSD test work, it fails. dmesg gives the following output when inserting the SD card:
[191153.839254] msm_pm_enter: limit c000fe34: pxo 0, l2_cache 0, vdd_mem 1, vdd_dig 1
[191153.839254] mpm_irq = 0, apps_irq = 0
[191153.839254] mpm_irq = 5, apps_irq = 392
[191153.839254] mpm_irq = 33, apps_irq = 382
[191153.839254] msm_mpm_irqs_detectable: cannot monitor 000000,00000000,00000000,00000000,00000000,00000000,00020000,00000000,00000000,00000000,00000000,00000000,00000000,00000000
[191153.839254] msm_pm_enter: return
[191153.839254] msm_gpio_show_resume_irq: 392 triggered
[191153.839254] gic_show_resume_irq: 48 triggered
[191153.839254] gic_show_resume_irq: 52 triggered
[191153.842550] PM: noirq resume of devices complete after 2.562 msecs
[191153.850241] pm8xxx_irq_block_handler: Show resume wakeup pmirq = 194
[191153.850790] PM: early resume of devices complete after 0.488 msecs
[191153.852591] pm8xxx_irq_block_handler: Show resume wakeup pmirq = 78
[191153.852896] keycode[115] is pressed
[191153.853049] mmc1: Slot status change detected (0 -> 1) and the card detect GPIO is ACTIVE_LOW
[191153.853049] wakeup wake lock: mmc1_detect
[191153.853140] [TP] synaptics_resume() +++
[191153.853140] [TP] synaptics_resume() ---
[191153.853171] l3gd20_gyr 12-006a: resume
[191153.854483] PM: resume of devices complete after 3.691 msecs
[191153.855765] msm_suspend_end, is_wakeup_from_pc = 1
[191153.866264] QSEECOM: qseecom_receive_req: Interrupted: exiting wait_rcv_req loop
[191153.866295] QSEECOM: qseecom_ioctl: failed qseecom_receive_req: -512
[191153.866325] QSEECOM: qseecom_receive_req: Interrupted: exiting wait_rcv_req loop
[191153.866356] QSEECOM: qseecom_ioctl: failed qseecom_receive_req: -512
[191153.855765] Restarting tasks ... done.
[191153.948333] PM: suspend exit 2015-11-02 22:06:35.266798842 UTC
[191153.948364] suspend: exit suspend, ret = 0 (2015-11-02 22:06:35.266829338 UTC)
[191154.054483] keycode[115] is released
[191154.162129] mmc1: host does not support reading read-only switch. assuming write-enable.
[191154.164235] mmc1: new high speed SDHC card at address b368
[191154.164265] mmc1: mmc_can_sanitize card is no
[191154.168935] mmcblk: probe of mmc1:b368 failed with error -28
So apparently the SD card recognition is triggered, but then fails. Any ideas?
May be, it is dead, asian sd-card are often self-destroy. Check with other device, sd-card recognized? Since some time my Transcend 16GB 10 class card not recognized too.
hyper_sonic ( 2015-11-03 08:12:42 +0200 )editfixed after two reboots
schmittlauch ( 2015-11-08 03:27:45 +0200 )edit