asked 2013-12-30 10:04:29 +0200
No problems when using headphones, but if phone is connected to stereo system with 3,5mm/RCA extension I get a low frequency buzz which is quite audible. No problems with other players when using the same configuration (iPod, computer etc.)
answered 2015-09-09 02:15:41 +0200
Jolla has an audio jack designed for headphones, not a line out designed for amplifiers. I don't know the exact values on Jolla, but typically headphone jack has a low (8-32 ohm) impedance, compared to hundreds (100-600 ohm) in a line out connector.
If the amplifier is a quality one, I'd try with 1/3 - 1/2 volume setting on Jolla (to reduce the signal noise to minimum) and higher volume setting on the amplifier.
If the amplifier is a low-end (car stereo), I'd suggest adding resistors (maybe 600 ohm serial, 100 ohm paraller) into the wire to get closer to typical line out impedance levels, aiming for a signal that the car stereo amplifier is designed for. Sound quality gets better, but notify very low max volume. Powerful amp required.
The best solution: Get a car stereo with Bluetooth audio. Digital signal doesn't mind the impedance ;)
answered 2014-01-12 13:43:02 +0200
From your description of the sounds I am not sure if this might be the case, but it could match.
Please note, that there are two different standards for connecting headsets via 3.5mm.
http://en.wikipedia.org/wiki/AHJ
and
http://en.wikipedia.org/wiki/OMTP
For example N900 and N9 both use OMTP, while Jolla (according to https://twitter.com/phlixi/status/412897182795055104) and most other devices today, like Galaxy / iPhone etc use AHJ.
When I use the original N9 Headset on e. g. a Galaxy Nexus, I get sounds, that could match your description. Fix: use AHJ connector.
I don't think that's the problem here. The headphones I tested are standard stereo headphones with only three 'bands' on the plug (L/R/Ground) - they work fine. The connecting cables to the car stereo are the exact same. They have the strange distortion. (Although I haven't tested it in a while, haven't had the time. Maybe it's better now or maybe it was just a problem with that specific cable.)
Edit: Just did a quick test at home pluging my Jolla into my Zoom H4, didn't notice any Distortion. Will have to try again with the car stereo.
Ozymandias ( 2014-01-12 14:23:41 +0200 )editWell of course it's true, I just don't think it has anything to do with the audio connection via normal audio cable.
Ozymandias ( 2014-01-28 11:16:42 +0200 )editanswered 2014-10-20 21:48:18 +0200
I've found a workaround for the issue. The problem seems to be the too high input impedance of the AUX-device. Headphones normally have a lower impedance.
You need a splitter cable similar to this that allows to connect two devices to the phone. (EDIT: take attention that it's not a cable that splits the left and the right channel, both female connectors need the left AND the right channel!)
In one output you plug your AUX-device, in the other you plug your earphones. The earphones are now parallel connected to the AUX-device and pulling down the impedance.
Alternatively you can solder yourself a small plug with resistors to pull down the impedance, that way the headphones don't need to be connected. (I haven't tried this yet and I don't know what resistance to choose but it should work too)
Could something like this help? http://www.amazon.com/3-5mm-Stereo-Patch-Cable-Resistors/dp/B004M49I26.
(I commented on the original question earlier by mistake. I ment the comment about plugs for sale for this answer.)
hetas ( 2014-10-21 22:12:15 +0200 )editanswered 2015-09-08 19:02:38 +0200
Old thread but I'll post my workaround anyway. I've been using Jolla in my car stereo using the aux connector. I've had this distortion problem and it's quite annoying.
I finally found a reasonably priced portable headphone amplifier from Creative. It's an extra device and cables in the car but seems to work. No more crackles.
I got mine from finnish e-shop jimms.fi for 40€. Battery can be charged with similar usb-cable as the phone. There's probably similar devices from different manufacturers.
(Actually the device I got was the E3 even though I ordered E1. So my experiences are based on that. E3 has bluetooth but I don't' use that at the moment. E1 could have been actually better for me. Power and volume buttons seem more practical in the cheaper model. But I'll keep the bluetooth model just in case.)
answered 2019-10-01 10:58:57 +0200
I had this problem with my Xperia XA2 kadt weekend. Connecting a phone to aux-in had been no problem with former iOS and Windows Mobile devices, and as far as I remember it also worked on the XA2 whike it was running with Android. So to my mind this must be a software problem in Sailfish OS and not a hardware restriction...
answered 2019-11-15 16:48:47 +0200
Updated to version to 3.2.0.12 solved the issue for me. I tried it again today in my car. Now Spotify works perfectly. Thanks Jolla. Hopefully it works for others as well.
answered 2017-10-27 13:28:04 +0200
This is a old post, but still thought of adding my comment. I have similar problem while connecting audio out from my Samsung Galaxy Note smartphone to Onkyo receiver which is from pre-smartphone era. Smartphone 3.5mm jack pin has 4 sections left, right channel, ground & microphone while the audio jack connected to Onkyo aux In has only 3 sections left, right channel & ground which inserting Onkyo aux In jack into smart phone to great extend it interfere with ground and mic connection which explains why if you turn the jack it works & attimes it doesnt. The solution I contemplate is to cut a smartphone ear phone near its ear piece, discarding mic wire and soldering rest left, right, ground to a 3.5mm female jack receiver with 3 pins only where Aux In jack sbould work like champ.
answered 2019-10-04 11:18:08 +0200
An app called Audio Output Chooser by ahappyhuman solved that issue for me (find in Storeman). Choose output to line and it should be fine. 👍
answered 2019-10-07 06:28:08 +0200
download audio output chooser in openrepos.net
answered 2014-10-03 08:50:05 +0200
Your cable could be picking up ambient electrical noise. Try using a shielded audio cable.
Asked: 2013-12-30 10:04:29 +0200
Seen: 70,572 times
Last updated: Nov 15 '19
Is the phone connected to its charger at the same time
rsainio ( 2013-12-30 10:27:53 +0200 )editNope! Granted, it sounds a bit like grounding buzz. Tried with an external mono speaker and no problems there. Someone else had a similar issue when connecting to car stereo (link in finnish) here
J_W_PEPPER ( 2013-12-30 10:54:37 +0200 )editI'll add to this that I was using the stock media player and FLAC audio file for playback. Haven't actually tried it again after the "Maadajävri" update. Will do so today.
J_W_PEPPER ( 2013-12-30 11:41:21 +0200 )editOh and I was afraid it might be just my phone. Yes, same here, headphones seem to be fine, car audio has very bad distortion going on, with the stock player as well as android GoneMad Player. Tried two different cables, same result, though it seemed that by turning the plug in the jack resulted in different kinds of distortion, one instance of really really quiet sound and on one occasion actually distortion-free, fine audio. I am swamped with work, so I couldn't test this more.
Ozymandias ( 2013-12-30 14:17:43 +0200 )editTested it again, same setup: not connected to charger, only 3,5 mm to aux extension, same result. The frequency was higher than I remembered. White noise, like a detuned radio. Tried turning the plug like Ozymandias, but no difference. Only some loud pops and contact noise.
J_W_PEPPER ( 2013-12-30 19:21:46 +0200 )edit